[산업/전자]렌즈접착제 Lens Bond TYPE M-65, MIL-A-3920
TYPE F-65
Type F-65 was developed mainly for its rapid, room temperature cure. With F-65, the engineer or researcher can test his systems in a few hours. Type F-65 also saves time in pilot and small production runs, or where curing ovens are not available. This cement is qualified to meet MIL-A-3920.
12200 |
Lens Bond Type F-65 |
4oz |
||
13000 |
Additional Catalyst |
3cc |
||
13003 |
Thinner (Monomeric styrene) |
4oz |
||
13004 |
Plasticizer Modifications |
.5-5% |
||
13008-A |
*Refractive Index Adjuster |
Approximate Curing Times
Room Temperature 22°(72°F) |
Oven Temperature 70°(160°F) | |||
---|---|---|---|---|
Catalyst Ratio | Pre-Cure | Full-Cure | Pre-Cure | Full-Cure |
2:100 | 60 minutes | 36 hours | Not Recommended | |
5:100 | 30 minutes | 1 day | Not Recommended | |
NOTE: Although we do not recommend complete oven curing, elements that have been pre-cured at room temperature for 30 minutes can then be placed in the oven to achieve a full cure in a half hour. The catalyst ratio shown is recommended as standard. Sufficient catalyst is supplied with each quantity. |
Instructions For Use
1. Preparation of Elements: Other than normal cleaning procedures, no special preparation is required. The best final cleaner is reagent grade or C.P. acetone.
2. Preparation of Cement: Prepare Type F-65 by the addition of catalyst to cement in a clear glass container. Thorough mixing is important. While stirring, hold container up to the light and observe the Schlieren Effect. When the Schlieren Effect disappears, continue mixing for at least 30 seconds. The entrapped air in the cement will surface if the mixture rests at room temperature for a short time, or is briefly subjected to a vacuum of 625mm Hg. (25" Hg.) Sufficient catalyst is supplied with Type F-65 cement for a 5:100 ratio (5 drops per 3ml of cement).
Safety: Although LENS BOND is quite safe to use, some persons may be sensitive to the chemicals comprising the formulation. For them, the use of finger cots or gloves is recommended. Adequate ventilation should be provided.
3. Application and Curing of Type F-65: Place the prepared LENS BOND on the concave surface, and place the convex surface thereon. Press down firmly and gently until LENS BOND completely wets the matching surfaces. Then, with a slow rotary motion and light pressure, force air bubbles from between the lenses. Excess Cement can be removed with a cloth slightly moistened with alcohol or acetone. (Excess solvent will remove cement from between the cemented components.) After pre-cure, holding devices can be removed and the components carefully cleaned. Before environmental testing, however, the lenses must be fully cured.
Full-cure time is in addition to the pre-cure time. If there is no reason to remove holding devices after pre-cure, components should be cured for the total time (pre-cure plus full-cure). If there is any doubt about cure being achieved, allow components to cure for a longer period of time. The Cement will not overcure. If cure is not achieved in a reasonable amount of time, the catalyst ratio, mixing procedure, and temperature should be checked.
Note: If the elements will undergo hostile environmental tests, allow 48 to 72 hours between full-cure and testing.
Specifications
Viscosity........................275 cps. to 320 cps. Refractive Index (full-cured)....1.55 at 25°C Refractive Index (uncured).......1.53 Operational Temperature Range....-54°C(-65°F) to 100°C(212°F) Youngs Modulus...................6.2 x 105lbs/in2 Shear Strength...................5200 lbs/in2 Impact...........................(.3 to .4)ft lb/in Specific Heat....................(.2 to .4) Cal/gm Dielectric Constant..............3 at 106 cps Loss Factor at 106 cps...........(.05) Water Absorption.................0.3% (24 hours. 25°C on bulk material) Dispersion Formula...............n=1.5754-(0.04742)-[0.0070/(2-0.028)]+
[0.0011/(2-0.028)2] Shrinkage on Cure................Approximately 4% pH...............................3.2 Specific Gravity.................1.22 Shore D. Hardness................Approximately 90 Surface Tension..................44 Dynes/cm. Linear Coefficient of Expansion..Approximately 6.3x10-5/°C at between 27°C-100°C 5.58x10-5/°@ between 100°C-200°C Thermal Conductivity.............500x10-6 cal(sec)(sq.cm)(°C)(cm) Flash Point (uncured)............50°C Glass Transition (Tg)............>90°C Outgassing TML...................2.6% Outgassing CVCM..................0.1% Shipping and Storage.............Type F-65 needs no special handling or storage. It should, however, be kept away from intense light and elevated temperatures. Shelf Life.......................18 months from date of manufacture Size.............................114 gm(4oz)
*The reference index may be increased to 1.59-1.61 with the use of our Cat# 13008, - Refractive Index Adjuster For technical data on adhesion properties, solvent and thermal resistance as well as transmission studies, please go to our technical data section on this site.
-
[산업]에폰스화학 상온경화형 에폭시 접착제 : AR-16, AR-13, AR-17
-
[산업] STYCAST 2651-40FR -> STYCAST ES 2505 몰딩,포팅
-
[산업/전자] ENSURE CP-7412SR 일액형 에폭시 접착제
-
[산업/전자] ENFORCE CP-7494C : 플라스틱 접착용 flexible 이액형 epoxy 접착제
-
[산업]에폰스화학공업 전기,전자용, 적층소재, 성형재, 바니쉬,함침
-
[산업] 에폰스화학공업 상온 경화용 접착제
-
[산업,건설]에폰스화학공업 BC-302 아스팔트,콭크리트,활주로용,활주로 배관매립용 에폭시
-
[산업/전자]일액형 열경화 에폭시 접착제(7405B)
-
[산업/전자]밀본드 시스템 (TYPE Milbond Adhesive System), MIL-A-48611
-
[산업/전자]렌즈 접착제(Lens Bond) Type EK-93, 에폭시 구조용 접착제
-
[산업/전자]렌즈접착제 Lens Bond TYPE DC-90 UV 경화후 상온 후 경화
-
[산업/전자] 렌즈접착제 Lens Bond Type RD3-74
-
[산업/전자]렌즈접착제 Lens Bond TYPE M-65, MIL-A-3920
-
[산업/전자]렌즈접착제 Lens Bond TYPE M-62, MIL-A-3920.
-
[산업/전자]렌즈접착제 Lens Bond Type C-59, MIL-A-392
-
[산업,전자]밀본드(mil bond) 1292 elastomeric-epoxy 접착제
-
[산업]하이솔(Hysol) 흑색,열경화 에폭시 몰딩제,언더필 UF3800
-
[산업]몰리테크 열전도성 에폭시 TR 1000,TR 2000,TR 4000, TR 5000
-
[산업/광학/접착/코팅] AREMCO-BOND 아렘코 전체 제품 다보기
-
[산업/광학] 아렘코 AREMCO-BOND EB-112 저점도 에폭시 접착제