[산업/전자] ESLAST ES-5227 : 일액형 습기 경화형 제품
PRODUCT DESCRIPTION
FOTOPOLYMER ESLAST ES-5227 is a single component, modified silicone based adhesive and sealant with excellent flexibility when cured upon exposure to moisture.
ESLAST ES-5227 is formulated with a non acidic and low odour chemistry that is neutral curing and does not react or corrode with most metals and plastics.
ESLAST ES-5227’s self levelling flow is developed for conformal coating and for penetrating into small crevices and voids in potting and sealing applications.
ESLAST ES-5227 cures with excellent environmental resistance and extremely high service temperature.
KEY FEATURES
- Very rapid curing with moisture for immediate fixturing and assembly
- Formulated for bonding, sealing, coating and potting applications
- Low viscosity for penetrating of preassembled parts and self levelling flow
- Suited for polymeric and inorganic substrates such as polycarbonate, polyamide, PET, glass, metal, ceramics etc
- Extremely high flexibility with very low hardness, low modulus and very high elongation
- Excellent protective resistance against weathering, moisture, ozone, vibrations, oils, chemicals, ultraviolet, mechanical impacts and temperature extremes
- Remains flexible and inert over a wide range of temperature
TYPICAL PROPERTIES OF UNCURED MATERIAL
Base : Modified silicone
Appearance : Translucent self levelling liquid
Viscosity @ 25°C : 30,000-40,000
Solids content, % : 98 (contains no solvents)
Specific gravity : 1.00-1.10
Odour : Mild
TYPICAL CURING PERFORMANCE
MOISTURE CURE
At 24°C and 50% relative humidity, ESLAST ES-5227 forms a layer of skin within 5 minutes upon exposure to surface or atmospheric moisture.
ESLAST ES-5227 beneath the skin continues to cure. Curing time is extended as the thickness of the bondline and volume of adhesive increases.
A bondline thickness of up to 5 millimetres can be curable after 24 hours.
Increased thickness may require 3 or 4 days for complete cure. Optimum conditions for moisture cure should be determined on the actual assemblies.
Not recommend for use in totally confined cure conditions where the sealant is not exposed to atmospheric moisture.
Recommended Curing Condition
Bondline temperature, °C : 25
Skin over duration, minutes : 5
Tack free duration, minutes : 15
TYPICAL PROPERTIES OF CURED MATERIAL
PHYSICAL PROPERTIES
Appearance Translucent elastomer
Hardness, Shore A 25
Elongation @ break, % 300
Tensile strength @ break, N/mm2 (PSI) 1.0-1.7 (150-250)
PERFORMANCE PROPERTIES
Peel strength , N/mm (PPI) 7.0 (40) T
HERMAL PROPERTIES
Temperature range, oC -60 to 260
Thermal conductivity, W/mK 0.42
ELECTRICAL PROPERTIES
Dielectric constant, 100 Hz 2.7
Dielectric strength, kv/mm 450
Volume resistivity, Ohm-cm 1.7 x 10E14
-
[전기/전자] 신에츠 RTV 이액형 실리콘 고무 목록 - 전기 특성, 내열성, 내한성 우수, UL승인품,열전도성
-
[전자] 신에츠 RTV 1액형 실리콘 제품 목록과 특징 - 씰링,고정, 코팅, 포팅
-
[산업/건축] 한신실리텍 - HS-BIO, SEALANT-BIO : 내구성, 내후성, 내열성, 내한성 등이 뛰어난 씰링재
-
[산업/건축] 한신실리텍 - HS300 :유리 창호,세라믹,알루미늄,목재, 콘크리트,벽돌 씰링
-
[산업] 세메다인 탄성 접착제 슈퍼 X (super X) - 고무 소재별 접착력
-
[산업] 세메다인 탄성 접착제 슈퍼 X (super X) - 소재(피착제)별 접착력
-
[산업] 세메다인 탄성 접착제 - 슈퍼 X (super X)
-
[건축/인테리어] 타일 줄눈 실란트 - ARDEX SE
-
[건축] 탑실 방화용 아크릴 실란트 489 : Dry-wall 구조체의 틈새나 케이블, 파이프
-
[산업] 울트라 본드 다용도 - SU : 속경화 일액형 접착제,플라스틱과 실리콘 접착
-
[산업] FOOD 그레이드, FDA 승인 - 식품시설이나 설비 주로 사용 / 748 실리콘 접착제
-
[산업] FOOD 등급, FDA 승인 제품 - 식품산업에 주로 사용 / 733 실리콘 접착제
-
[산업] FDA 승인, FOOD 그레이드 실리콘 접착제,씰링제
-
[산업/전자] ESLAST ES-5227 : 일액형 습기 경화형 제품
-
[산업]몰리테크 열전도성 실리콘
-
[전자,산업]KCC : 실리콘 오일의 종류 - 기계, 전자, 화학, 섬유, 종이, 건축, 토목 및 화장품 산업분야
-
[산업/씰링] 아렘코 AREMCO-BOND 542,503-VFG-C,CP2000,CP2070,CP4010 씰러
-
[산업] 아렘코(AREMCO) Heat-Away™ 열전도성 구리스 637,638,639,640,641-EV
-
[산업] 아렘코(AREMCO) Aremco-Bond 542,503-VFG-C High Temperature Thermal Spray Sealants
-
[건축/건설]노바텍 Rock7 다목적 탄성 폴리머 접착제 및 충진제